Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
- Controls and receptions of safe operation of the car
Specifications
Instrument guard and signalling devices
Unlocking and lock-out of locks of the car, management стеклоподъемниками
Switches
The ignition switch, transmission and темпостат
Systems of ventilation, heating and air conditioning
Audiosystem
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
The ignition lock, transmission and темпостат
The switch of ignition and blocking of a steering column
|
|
Never take out a key during car movement as it will lead to blocking of a steering wheel and driving loss. Do not leave a key in position «ON» if the engine does not work. Thus the accumulator can be discharged, and ignition can be damaged.
|
|
|
At a complete set of the car system of blocking of the engine, at вынимании a key the system of blocking of the engine will automatically work.
|
|
|
The switch of ignition and blocking of a steering column is located to the right of a steering column (address to an accompanying illustration). |
The description of position of the ignition key in the lock is more low resulted.
«START» – starter inclusion. The key will return to position «ON» at отпускании.
«ON» – inclusion of the engine and auxiliaries of all kinds. This normal position at driving.
«АСС» – auxiliary devices, such as a radio receiver, work, however the engine is switched off.
«LOCK» – the engine is switched off, and the steering wheel is blocked. The key can be taken out only in this position. It is necessary to press a key to turn it from position «АСС» in position «LOCK». If a key will take out, the system of blocking of the engine will be automatically established. At start of the engine the key can seem got stuck in position «LOCK» (blocking). For its clearing from this position at first be convinced that the key is pressed against the stop, and then slightly повращайте a steering wheel, cautiously turning a key.
Automatic transmission
The selector lever, switches of modes АТ of model Toyota Land Cruiser and their description it is resulted on an accompanying illustration.
Controls transmission of models Lexus LX 470 see in Controls and receptions of safe operation of the car.
|
|
At regulator use темпостата, even at inclusion of lowering transfer by deenergizing of raising transfer, braking by the engine will not be carried out, as is involved темпостат. |
System of distribution of a twisting moment between driving wheels
System of blocking of interaxal differential
|
|
Use the lever of a choice of a mode and the switch of blocking of interaxal differential (address to an accompanying illustration) for a choice of following modes of a distributing box and interaxal differential. |
«Н» (A position of raising transfers)
The position «Н» of the lever of a regulator of a full drive provides a mode of blocking or an unblocking of interaxal differential depending on a position of the corresponding button.
Use this position at the unblocked interaxal differential for normal driving on all types of roads, from dry roads with a firm covering to wet roads, and also the roads covered with ice or snow. This position provides the big economy, more silent driving, the least deterioration and the best driving.
Use this position at the blocked interaxal differential for draught increase, at sensation of loss of capacity, for example, at sliding of wheels in a mode «Н» with the unblocked interaxal differential.
«N» (Neutral position) To wheels it is not transferred to any capacity. Use this position only at management лебедкой or other equipment. The car should be stopped.
«L» (Position of lowering transfers, interaxal differential it is blocked) Use this position for the maximum capacity and draught. Use position «L» under trying conditions driving when the car badly gives in to management even in a mode «Н» with the blocked interaxal differential.
Inclusion of a control lamp of blocking of interaxal differential testifies to blocking activation.
Keep in mind that if not К/Л dies away by pressing of the button of blocking of interaxal differential, conduct the car directly at acceleration or delay or be developed.
Switching procedure
|
|
1. For switching between modes of an unblocking and position blocking «Н» press the button of blocking of interaxal differential.
2. For switching between transfers «H» and «L» stop the car, establish a transmission in position «N» and switch a control lever a drive to four wheels.
|
|
Never switch the lever of a regulator of a drive to four wheels in case of car sliding. Before to carry out switching, stop sliding or car spinning. |
|
|
System of blocking of forward and back differentials
|
|
1. The system of blocking of forward and back differentials is intended for use only in case of proslipping of wheels in a ditch or on slippery or rough road. This system is effective in case of slipping of one of wheels or one right or one left pair wheels.
|
|
Do not use blocking of back differential in the conditions different from resulted above. The big efforts of a steering and cautious management at performance of turns otherwise be required. Especially use of forward differential as addition to back extremely will complicate a steering and can lead to drift of the car during acceleration or engine braking. |
2. For blocking of back differential press and turn the switch clockwise, yet will not hear click. If it does not help, turn the switch clockwise against the stop to block forward differential in addition to the back.
3. On forget to stop the car before performance of blocking of differential.
4. For simple blocking turn the switch of blocking and cautiously press an accelerator pedal.
5. If the switch is in the included position, the control lamp will blink. Wait some seconds while the system will not finish operation. After the differential will be blocked, the control lamp will stop to blink and will burn constantly.
6. If the back differential is blocked, the antiblocking brake system does not work. If the control lamp «ABS» at this time lights up, it is normal.
|
|
Do not block differential until wheels will not stop slipping. Otherwise the car can move in an unforeseen direction if the differential is blocked that can lead to possible damage of components of blocking of differential. Do not drive the car for the speed over 8 km/h if the differential is blocked.
|
7. To unblock differential, turn the switch against the stop counter-clockwise.
8. Unblock differential as soon as the car will get under way from a place.
9. For a simple unblocking slightly turn a steering wheel in any direction at car movement.
10. If the differential is deduced from gearing, the control lamp will go out.
11. The differential also will be unblocked at switching of the lever of a regulator of a drive on four wheels in position «Н». Do not forget to establish the switch in the switched off position after use of this function.
12. For check of a display lamp turn the ignition key in position «ON», however do not start the engine. |
|
System of blocking of back differential
The system of blocking of back differential is intended for use only in case of proslipping of wheels in a ditch or on slippery/rough road.
This system of blocking of differential is effective in case of slipping of one of back wheels.
|
|
1. For blocking of back differential press and turn the switch clockwise, yet will not hear click.
2. Do not forget to stop the car before performance of blocking of differential.
3. For simple blocking turn the switch of blocking and cautiously press an accelerator pedal.
4. If the switch is in the included position, the control lamp will blink. Wait some seconds while the system will not finish operation. After the differential will be blocked, К/Л will stop to blink and will burn constantly.
5. If the back differential is blocked, system ABS does not work. If at this time will light up К/Л systems ABS, it is normal.
|
|
Do not block differential until wheels will not stop slipping. Otherwise the car can move in an unforeseen direction if the differential is blocked that can lead to road and transport incident. It can lead also to possible damage of components of blocking of differential. Do not drive the car for the speed over 8 km/h if the differential is blocked. |
6. To unblock differential, turn the switch against the stop counter-clockwise.
7. Unblock differential as soon as the car will get under way from a place.
8. For a simple unblocking slightly turn a steering wheel in any direction at car movement.
9. If the differential is deduced from gearing, the control lamp will go out.
10. The differential also will be unblocked, if you switch the lever of a regulator of a drive to four wheels in position «Н». Do not forget to establish the switch in the switched off position after use of this function.
11. For check of a display lamp turn the ignition key in position «ON», however do not start the engine. |
|
Control system of speed (Темпостат)
Speed control function allows to conduct the car on desirable speed over 40 km/h even if to clean a foot from an accelerator pedal.
Speed can be supported at higher or low level within the engine characteristic though little change of speed can occur at transition to raising or lowering transfer. On abrupt slopes can occur большее change of speed, therefore is better conduct the car without resorting to темпостату.
|
|
For maintenance of the maximum control over movement of the car do not use темпостат at driving in the conditions of heavy traffic of transport either at changing traffic conditions or on slippery (wet, covered with ice or snow) roads, and also at a strong wind. Avoid increase in speed at movement downwards on descent. If speed of the car too fast, disconnect темпостат and pass to lowering transfer for use of braking by the engine for the purpose of delay.
|
Inclusion and system deenergizing
|
|
For management темпостатом press the button «CRUISE ON OFF». Thus burning control lamp on a control panel will show that now it is possible to establish desirable speed of the car. By the second pressing the system will be completely switched off.
|
|
In order to avoid casual inclusion темпостата hold the switch «CRUISE ON OFF» switched off if you do not use темпостат. |
|
|
Choice of cruiser speed
|
|
1. Disperse the car till demanded speed, press a regulator downwards in a direction «SET/COAST» and release it further chosen a high-speed mode it will be supported темпостатом automatically.
2. If speed is not satisfactory, move the lever upwards for faster speed or move downwards for lower speed. Everyone отжимание changes installation of speed to 1.6 km/hour. After installation of speed it is possible to clean a foot from an accelerator pedal.
3. In need of acceleration for example, at overtaking clamp a pedal of an accelerator with sufficient force to exceed the established speed. If to release a pedal, the car will return to the speed established before performance of acceleration. |
|
Cancellation of the chosen high-speed mode
|
|
1. To cancel the chosen high-speed mode it is possible having pressed a brake pedal, or having pulled the lever in a direction «CANCEL» and having released it.
2. If speed of the car goes down below 40 km/h, the chosen high-speed mode will be automatically excellent.
3. If speed of the car falls more than 16 km/h below the chosen value, cruiser installations also will be automatically cancelled.
4. If cancellation of the chosen high-speed mode occurs on any to other, distinct from listed above, the reasons, check up the car at representative Toyota or Lexus at the first possibility. |
|
Return to a cruiser mode after compulsory decrease in speed
|
|
1. Press the lever upwards in a direction «RES/АСС» and take it in this position. Release the lever when desirable speed will be reached. At that time while the lever will be pressed, the car will gradually speed up.
2. However more likely to return to higher speed, it is necessary to accelerate a car course, and then to press the lever downwards in a direction «SET/COAST». |
|
Return to a cruiser mode after compulsory acceleration
|
|
1. Press the lever downwards in a direction «SET/COAST» and take it in this position. Release the lever when desirable speed will be reached. While the lever will be pressed, the car will gradually reduce speed.
2. However more likely to return to lower speed, it is necessary to reduce speed of the car, and then to press the lever downwards in a direction «SET/COAST».
3. Even if to switch off raising transfer at included темпостате, braking by the engine will not be carried out, because is not switched off темпостат. For reduction of speed of the car return to slower speed by means of the lever темпостата or pressing of a brake pedal. If the brake pedal is used, темпостат will be switched off. |
|
Renewal of preliminary established speed
|
|
1. If preliminary established speed has been cancelled by switching of the lever of a regulator, or pressing of a pedal of a brake by lever pressing upwards in a direction «RES/АСС» the speed established before cancellation will be restored.
2. However if speed of the car falls below 40 km/h, preliminary established speed will not be renewed. |
|
Warning signal about malfunction in system темпостата
|
|
|
1. If the control lamp «CRUISE» on a control panel blinks at use темпостата, press the button «CRUISE ON OFF» for system deenergizing, and then press the button again for system inclusion.
2. In case there will be one of following actions, in темпостате there are malfunctions.
- The control lamp does not burn.
- The control lamp blinks again.
- The control lamp dies away after высвечивания.
3. In this case address to representative Toyota for car check.
|
|
|
|