Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation



Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of forward shock-absorbers
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of assemblage of a rotary fist from a nave
   Check of a condition and replacement of spherical support
   Removal and installation торсионных bars
   Removal and installation of the top operating lever of a forward suspension bracket
   Removal and installation of the bottom operating lever of a forward suspension bracket
   Removal and installation of back shock-absorbers
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of a jet bar
   Removal and installation of a screw spring of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and steering wheel installation
   Condition check, removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment





Suspension bracket and steering

Forward suspension bracket

The forward suspension bracket has an independent design. Rotary fists are connected by the top and bottom levers of a suspension bracket (operating levers) by means of spherical support. The opposite ends levers приболчены to a frame. The stabilizer of cross-section stability reducing rocking and a list of the car on turns enters into a regular complete set.

Instead of screw springs are used торсионные bars which fasten to the top levers of a suspension bracket.
The basis of a forward suspension bracket is made by telescopic shock-absorbers. The bottom support of shock-absorbers приболчены to the bottom levers of a suspension bracket. The top ends of shock-absorbers are fixed in basic arms of a bearing frame.

Back suspension bracket

Components of a back suspension bracket

1 — the Bottom lever of a suspension bracket
2 — the Top lever of a suspension bracket
3 — the Screw spring
4 — Collars of fastening of a bar of the stabilizer of cross-section stability
5 — the Bar of the stabilizer of cross-section stability

6 — the Back bridge
7 — the Plug of the top lever of a suspension bracket
8 — the Shock-absorber
9 — the Rack of a bar of the stabilizer of cross-section stability
10 — the Bottom support of the shock-absorber


The back suspension bracket is organised by means of pair the screw springs, two telescopic shock-absorbers, four levers (two bottom and two top) and the jet bar connecting the left end of the bridge with a beam of the bearing frame. The bar of the stabilizer of cross-section stability приболчена to assemblage of the back bridge also fastens to a frame of the car by means of two racks (address to an illustration above).

Steering drive

Considered models are equipped by the hydrostrengthened steering transfer реечного the type, connected to rotary fists by means of two steering draughts. Carter of the mechanism fastens to a cross-section beam.

Often in the course of service of components of a suspension bracket and a steering drive it is necessary to face with resistant отдаванию fixture.« Прикипание »fixture elements it is connected by that they are constantly subject to external influences, are in contact to water, a dirt, a soot and other promoting development of corrosion by substances. For the purpose of simplification of procedure отдавания its such"become attached"fixture it is necessary to impregnate with plentiful quantity of getting oil beforehand. Зачистка open carving parts of fixture a rigid wire brush also promotes simplification отдавания приржавевших nuts. Sometimes, in especially hard cases, for отпускания "the become attached" bolt/nut it is possible to take advantage выколоткой. Выколотка rests against edge шлица bolt nuts/heads, then sharp blows by a hammer are struck to its opposite end. Watch that выколотка has broken, try to damage inexact blows a carving. Effective enough way is also warming up resistant отдаванию fixture and a surface of a component surrounding it a torch of a blowtorch or a gas torch though composers of the given Management and do not recommend to resort without extreme need to such technology in view of its potential danger connected with possibility of ignition and risk of reception of burns. Any extension pieces, collars and trumpet nozzles are intended for twisting moment increase at отпускании fixture on them. However, remember that it is not necessary to use such intensifying adaptations complete with the drive equipped with "rattle" – the risk of failure of the ratchet mechanism is too great. Sometimes "the become attached" fixture starts to give in after preliminary slightly will be tightened clockwise. All fixture, отпускание which has demanded application of not ordinary measures at assemblage is subject to replacement!

After отдавания fixture attentively check its condition and in case of need make its replacement with elements of the same standard size. At assemblage tighten elements of fixture of components of a suspension bracket and a steering it is strict with demanded effort.


At all do not undertake attempts рихтовки the deformed components of a suspension bracket and a steering – аменяйте defective details new!

As procedures of service of components of a suspension bracket are carried out under the car, it is necessary to take care in advance of possibilities of lifting of a vehicle and its fixing in the lifted position (prepare reliable a jack and props).

At all do not perform any works under the car, fixed in the lifted position only by means of a jack!