Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation



Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of forward shock-absorbers
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of assemblage of a rotary fist from a nave
   Check of a condition and replacement of spherical support
   Removal and installation торсионных bars
   Removal and installation of the top operating lever of a forward suspension bracket
   Removal and installation of the bottom operating lever of a forward suspension bracket
   Removal and installation of back shock-absorbers
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of a jet bar
   Removal and installation of a screw spring of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and steering wheel installation
   Condition check, removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Производство фасадов мдф с плёнкой ПВХ в спб Optimaglass.



Removal and steering wheel installation

Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Onboard electric equipment see). Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation. In order to avoid system SRS damage, track, that the steering shaft was not turned after steering wheel removal. Block a column the ignition key at rectilinear position of forward wheels.


 PERFORMANCE ORDER

1. Result forward wheels of the car in rectilinear position. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. On in appropriate way the equipped models make deactivation SRS (the Onboard electric equipment see).
3. Having hooked, remove two plastic заглушки, established on lateral surfaces of assemblage of a steering wheel and ослабьте the screws of fastening of the module of a pillow of safety located in opened nests (address to an accompanying illustration). The turned out screws remain fixed in the nests.
4. Remove from assemblage of a steering wheel the module of a pillow of safety.

Try not to turn the removed module of a pillow of safety a face sheet to itself! Lay the module a face sheet upwards in a safe place.

5. Disconnect disturbing to removal of a steering wheel electroconducting.
6. Give a nut of fastening of a steering wheel, then with a paint mark position of assemblage concerning a steering shaft (address to an accompanying illustration).
7. By means of a special stripper remove a wheel from a steering column (address to an accompanying illustration).

In order to avoid infringement of centering of contact cable drum SRS do not suppose проворачивания a steering shaft at the removed steering wheel. At the compelled infringement of the given requirement the drum should be centered before wheel installation into place.

8. Make sure of correctness of centering of contact cable drum SRS, a share of that manually develop its casing counter-clockwise till the moment of occurrence of hard resistance, then return it approximately on three turns back and achieve combination стрелочных labels.
9. Establish a steering wheel on the regular place, having tracked correctness of combination of the landing labels put in the course of dismantle. Tighten a fixing nut with demanded effort.