Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation



Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of forward shock-absorbers
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of assemblage of a rotary fist from a nave
   Check of a condition and replacement of spherical support
   Removal and installation торсионных bars
   Removal and installation of the top operating lever of a forward suspension bracket
   Removal and installation of the bottom operating lever of a forward suspension bracket
   Removal and installation of back shock-absorbers
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of a jet bar
   Removal and installation of a screw spring of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and steering wheel installation
   Condition check, removal and installation of draughts of a steering drive
   Replacement of protective covers of assemblage of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Wheels and tyres - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


какие куры несут зеленые и голубые яйца



Removal and installation торсионных bars

Removal

Assemblage components торсионной bars


 PERFORMANCE ORDER

1. As elastic elements on models Land Cruiser Amazon are applied торсионные the bars using a principle of elasticity of twisting. Torsionnye bars are established in parallel road. It gives the chance designing of more compact designs of suspension brackets and the best controllability of a suspension bracket as there is no necessity for the big courses of an elastic element. Torsionnye bars usually are in the loaded condition and at their removal care is required.

After removal торсионных bars are very important not for mixing them in places; if necessary put a paint the labels specifying in the forward and back end торсионной bars and the party of the car from which it is removed (address to an illustration).

If them to establish not on the place or "back to front", торсионные bars can break. New торсионные bars are marked by letters L (left) or R (right) and an arrow specifying in a direction of braiding loading (address to an illustration).

2. Cock a lay brake. Ослабьте nuts of fastening of a corresponding forward wheel, поддомкратьте redock of the car also establish it on props. Remove a wheel.
3. At a corresponding complete set remove protection картера.
4. Put labels on торсионную a bar, анкерный and торсионный levers (address to an illustration in the Section beginning).
5. Measure distance "And" between an adjusting bolt анкерного the lever and a frame (address to an accompanying illustration). It is required at assemblage.
6. Ослабьте анкерный the lever before full easing торсионной bars.
7. Measure distance "In". It is required at assemblage (address to an accompanying illustration).
8. Turn out an adjusting bolt from анкерного the lever.
9. Remove saddles анкерного the lever.
10. Remove торсионную a bar with анкерным the lever.
11. Remove анкерный the lever with торсионной bars and rearrange it on a new bar.
12. Give two nuts with bolts and remove торсионную a bar.

Installation

 PERFORMANCE ORDER

1. Establish торсионный the lever, having wrapped bolts with nuts with demanded effort.
2. Establish a bar in торсионный the lever.
3. Establish saddles and an adjusting bolt.
4. Compare length of an adjusting bolt with measured in removal process.
5. Tighten an adjusting bolt so that distance "And" corresponded to requirements of Specifications.
6. If establish old торсионную a bar, establish it in анкерный the lever, combine preliminary put labels. Then, having combined labels of a bar and торсионного the lever, establish торсион.
7. Tighten an adjusting bolt so that distance "And" was equally measured at removal.
8. The further installation is made upside-down.