Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation



Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
- Engine electric equipment
   Specifications
   Start of the engine from the auxiliary power supply
   Removal and installation of the storage battery
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information and safety measures (petrol models)
   Check of functioning of system of ignition
   Replacement of the coil of ignition
   Check and adjustment of installation of a corner of an advancing of ignition/injection of fuel of the petrol engine
   Replacement of the module of ignition
   Charge system - the general information and safety measures
   Check of a condition of system of a charge
   Removal and generator installation
   Check of a condition and replacement of components of the generator
   Start system - the general information and safety measures
   Check of serviceability of functioning of a starter and start chain
   Removal and starter installation
   Removal and installation of the traction relay
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Check of a condition and replacement of components of the generator

Dismantling

Typical design of the automobile generator of an alternating current

1 — the Pulley
2 — the Cover from outside a drive
3 — the Forward bearing
4 — the Holder
5 — the Rotor
6 — the Back bearing
7 — a bearing Cover
8 — Rubber изоляционная an insert

9 — the Spring
10 — the Brush
11 — a pressure Regulator
12 — the Cover from outside contact rings
13 — the Holder выпрямительной assemblages
14 — Klemmnyj an insulator
15 — ShChetkoderzhatel with a cover
16 — the Back cover


 PERFORMANCE ORDER

1. Remove the generator from the engine (see Has undressed Removal and generator installation) and lay it on a pure workbench.
2. Give nuts of fastening of a back cover, release a plug nut In, throw off from the plug a washer and изоляционную the plug, then uncover (address to an illustration above).
3. Turn out screws of fastening of a regulator of pressure and щеткодержателя.
4. Remove щеткодержатель and a regulator of pressure from a back end face of a frame. If dismantling was made for the purpose of regulator replacement, pass to performance of procedure of paragraph 8, establish the new block, collect the generator and establish it on the engine (the Section Check of a condition of system of a charge see). In below-mentioned paragraphs the description of procedure of replacement of brushes is resulted.
5. Measure size выступания by each of brushes if results of measurements leave for the bottom border of an admissible range (see Specifications), replace brushes in gathering with the holder.

On some models the soldering iron can be necessary for replacement of brushes.

6. Check up smoothness of a course of brushes in directing holder.
7. Remove выпрямительную assemblage. Remove four rubber изоляционных inserts and a sealing plate.
8. By means of a marker or чертилки mark mutual adjusting position of forward and back casings of the generator.
9. Give a fixing nut and remove приводной a pulley with роторного a generator shaft.
10. Give four fixing nuts have undressed generating assemblage on two parts.
11. Remove a persistent washer and take a rotor from a forward part of assemblage.

Check

 PERFORMANCE ORDER

1. Measure resistance between two sliding contact rings (address to an accompanying illustration), the rating value makes 2 – 4 Ohm. Make sure of absence of conductivity between each of contact rings and роторной assemblage. At negative results of check, and also in case of excessive deterioration of contact rings replace a rotor.
2. Check up on breakage статорные generator windings, conductivity should take place between each pair face plugs of assemblage. If in any of measurements the ohmmeter gives out the infinite indication, replace статор. Check up windings on presence of signs of breakdown on weight (conductivity presence between the plug and a frame. Defective статор is subject to replacement.
3. Check up serviceability of a condition of positive and negative section of the rectifier.   
   a. It is necessary to begin with check of positive section, – assemblage should have conductivity only in one of directions, polarity change should lead to situation change on opposite (address to an accompanying illustration). It is necessary to check up each of assemblage plugs serially;
   b. Further pass to check of negative section, – operate in a similar manner (address to an accompanying illustration).

Assemblage

 PERFORMANCE ORDER

1. Installation of components is made as it should be the return to an order of their dismantle. Pay attention an order of performance of procedures.
2. At landing щеткодержателя on a generator shaft it is necessary to wring out serially by means of a small screw-driver each of coal brushes.
3. Screw fastening screws щеткодержателя and a pressure regulator.
4. Track reliability of a tightening of three nuts of fastening of a back cover.
5. Collect клеммную assemblage and fix its components the nut.
6. Establish the generator on the engine (see Has undressed Removal and generator installation).