Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation

Removal and installation of the aerial of a radio receiver

The description of procedure of dismantle of the aerial of external type is more low resulted. Some models are equipped by the aerial pasted on a windscreen, service of such aerials lies out of limits of qualification of the average mechanic-fan and it should be entrusted to experts of car-care centre.

PERFORMANCE ORDER

Remove a radio receiver and disconnect from it an antenna cable (see Has undressed Removal and installation of an audiosystem and it динамиков). "Walk" on an antenna cable, liberating it from intermediate clamps. Tie up by the end of a cable a string piece. The line of a lining of a cable of the aerial is presented on an accompanying illustration.

The aerial with the fixed mast

PERFORMANCE ORDER

1. By means of small рожкового a key of the suitable size turn out a mast of the aerial from the basis.

2. Give a nut of fastening of assemblage of the basis of an antenna mast (address to an accompanying illustration), take advantage of flat-nose pliers for removal of lock rings. Having pulled, take outside an antenna cable (leave the string tied up to a cable passed in an aperture under mast installation. Carefully remove all traces of a dirt and a rust from a place крепленияантенны.

3. Tie up to a string a cable of the new aerial and involve it inside кузовного an element.
4. The further installation is made as it should be the return to an order of dismantle of components.

The aerial with электроприводной a mast

For performance of the given procedure the help of the assistant is required.

The system contains the relay. If the aerial drive has ceased to function, first of all, check up the relay. The drive E/motor seldom fails.

PERFORMANCE ORDER

1. If disconnected, connect the storage battery and turn the ignition key in position LOCK.
2. Give a nut of fastening of the basis of an antenna mast (address to an illustration above).
3. Further one person should be in salon of the car, the second – to keep an antenna mast. Ask the assistant to press simultaneously button AM/FM on control panels of a radio receiver and to turn the ignition key in position АСС, the antenna mast should be put forward for all length of the course then it can be disconnected from приводного the electromotor. Remove a mast, the ignition key leave in position АСС.

4a. Remove локер protection of a wheel arch of a corresponding wing of the car (the Body see the Head) and отболтите from a wing the electromotor of a drive of an antenna mast. Completely extend an antenna cable outside, having left the string tied up to it passed in an aperture in кузовном an element (address to an accompanying illustration).

4b. Release three clamps and remove the panel of facing of a wheel arch, then give a fixing bolt and remove приводной the electromotor (address to an accompanying illustration).

4с. Polarity of plugs a socket of the electromotor of a drive of the aerial look on an accompanying illustration.

5. Tie up to left passed through кузовную the panel to a string a cable of the new aerial and involve it back in car salon.
6. Establish on the regular place the electromotor of a drive of an antenna mast.
7. Establish an antenna mast, having developed a cable the gear party forward on the car.
8. Turn the ignition key in position LOCK, the cable should be winded, and the mast to be involved in a wing.

If the key for any reason has been earlier translated from position АСС in position LOCK, repeat the procedure described in paragraph 8. If at key turn in position LOCK the cable does not start to be taken up, stir it on an input in the mechanism that the bottom end was developed and has been grasped by the coil.

9. Screw a nut of fastening of the basis of an antenna mast even if last was not up to the end involved yet in the panel covered. The mast should be involved definitively at нажимании on any of buttons of a choice of a radio range on the control panel by a radio receiver.
10. The further installation is made as it should be the return to an order of dismantle of components.