Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation



Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
- The engine
   + Typical procedures of service of engines
   + Procedures of service of the petrol engine
   - Procedures of service of the diesel engine
      Removal, installation, dismantling and assemblage of a head of cylinders
      Removal and installation of the inlet pipeline and final collector
      Removal, check of a condition and installation of a belt of drive ГРМ
      Removal and installation of cogwheels of drive ГРМ
      Replacement of a forward epiploon of a cranked shaft and epiploons of a camshaft and ТНВД
      Replacement of a back epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of valves
      Removal and pallet installation картера the engine
      Removal, check of a condition and installation of the oil pump
      Removal and installation маслоохладителя
      Removal and installation приводного a disk
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation of cogwheels of drive ГРМ

Components of drive ГРМ (a part 1)

1 — the Clip
2, 21 — the Vacuum hose
3, 28, 33, 34 — the Sealing washer
4 — the Cover of a gear belt
5 — the Flange №2
6 — the Clip
7 — the Flange №1
8 — a camshaft Cogwheel
9 — Natjazhitel of a gear belt
10 — the Tension roller
11 — the Flat washer
12 — the Clip (models with system ERG)
13 — a camshaft Cogwheel
14 — Shponka of a camshaft

15 — Privodnoj a belt
16 — the Fan
17 — the Pulley of a drive of the water pump
18 — the Cover of a head of cylinders
19, 23, 27, 31 — the Lining
20 — the Heater on an input
22 — the Inlet branch pipe
24 — Assemblage of an inlet branch pipe
25 — valve EGR Arm
26 — the Thermofilter
29 — the Vacuum hose (models with system ERG)
30 — the Gear belt
32 — the Filter

Components of drive ГРМ (a part 2)

1 — the Sealing ring
2 — the Pulley of a cranked shaft
3 — the Forward epiploon of a cranked shaft
4 — the Epiploon of cogwheel ТНВД
5 — the Persistent plate
6 — the Intermediate cogwheel
7 — the Cogwheel of a drive of the oil pump
8 — the Shaft of an intermediate cogwheel
9 — the Cogwheel of drive ТНВД and ГРМ
10 — the Sealing ring
11 — the Bearing of cogwheel ТНВД

12 — Cogwheel ТНВД
13 — the Thermofilter №2 blocks of cylinders
14 — a camshaft Epiploon
15 — the Back cover of a belt of drive ГРМ
16 — the Cover of cogwheels of drive ГРМ
17 — the Clip
18 — the Lining
19 — the Arm
20 — the Oil tube
21 — the Lining
22 — the Vacuum pump

Removal

 PERFORMANCE ORDER

1. Components of drive ГРМ are presented on illustrations above.
2. Remove приводной a belt.
3. Remove a belt of drive ГРМ and cogwheels of camshafts
4. Remove a back cover of a belt of drive ГРМ
5. Turn out two fixing bolts and remove маслопровод the vacuum pump
6. Remove the vacuum pump.
7. Block a cranked shaft and turn out the central bolt of its pulley (address to an accompanying illustration).
8. Remove the prorate and by means of a stripper dismantle a pulley of a cranked shaft.
9. Turn out 14 bolts of fastening of a cover of cogwheels of drive ГРМ.
10. Measure an axial backlash of an intermediate cogwheel and if necessary replace its persistent plate, a shaft, or a cogwheel.
11. Remove a cogwheel of a drive of the oil pump by means of a stripper.
12. Turn out two bolts, remove a persistent plate, a cogwheel and its axis.
13. Block cogwheel ТНВД, give a nut of its fastening and remove a cogwheel.

Stripper bolts roll no more, than on 8 mm.

14. Dismantle a cogwheel of drive ТНВД and ГРМ.

Installation

 PERFORMANCE ORDER

1. Installation is made upside-down.
2. For installation of an intermediate cogwheel turn leading cogwheel ТНВД so that the label «3» on a cogwheel of a cranked shaft was combined with a label «4» on leading cogwheel ТНВД. Then enter cogwheels into gearing (address to an accompanying illustration).