Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
- The power supply system and release of the fulfilled gases
Specifications
Sbrasyvanie pressure in the power supply system
Check of serviceability of functioning of the fuel pump, measurement of pressure of fuel
Check of a condition and replacement of fuel lines and them штуцерных connections
Removal and installation of a fuel tank
Cleaning and repair of a fuel tank - the general data
Removal and installation of the fuel pump
Replacement of the gauge of the expense of fuel
Removal and installation of assemblage of an air cleaner
Removal, installation and adjustment of a cable of an accelerator
System of electronic injection of fuel (EFI) - the general information
Check of serviceability of functioning of system of electronic injection
Check of a condition and replacement of components of system of injection
Release system - the general information
Removal and installation of atomizers
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Check of a condition and replacement of fuel lines and them штуцерных connections
|
1. Lines of a fuel path of the power supply system are laid between a petrol tank and an impellent compartment. Steel tubes and flexible fuel hoses fasten to the bottom of the car by means of clips and screw fixture. Each time when the car rises over the earth with any purpose (for example, for survey or replacement of components of system of release of the fulfilled gases), try to take advantage of a case and to check up a condition of fuel lines and them штуцерных connections. 2. Attentively examine all hoses and tubes of a fuel path on presence of cracks, twisting, deformations and other mechanical damages. 3. At revealing of signs of internal pollution or passableness infringement corresponding section of a fuel path it is necessary to remove and blow compressed air. 4. Make sure of reliability of a tightening of all штуцерных connections of hoses and metal tubes of a fuel path. |
|
Steel tubes
|
1. Use as replaceable sections only high-strength steel tubes of manufacture of the proved manufacturers. 2. Remember that copper and aluminium tubes are not capable to sustain vibrating loadings arising while in service the car. 3. Do not forget that fuel lines on the models equipped with system of injection, should maintain high internal pressure. 4. Often in firm shops of automobile accessories it is possible to get equipped carving штуцерными nozzles of section of metal tubes. At easing and a tightening штуцерных connections use two wrenches to avoid проворачивания a reciprocal part of a socket. Without fail check a condition used for hermetic sealing штуцерных connections of sealing rings. The worn out or mechanically damaged rings at once replace. Try to use as replaceable components only firm details. |
|
Flexible hoses
|
At replacement of fuel hoses use only the firm components calculated on high internal pressure.
|
Flexible fuel hoses should be laid not more close than in 10 sm from components of system of release of the fulfilled gases and is not closer than in 25 sm from каталитического than the converter. Watch, that fuel lines did not adjoin with кузовными elements and suspension bracket components.
Replacement
|
1. Dump pressure in the power supply system (Razdel Sbrasyvanie of pressure in the power supply system see). 2. Liberate section of a fuel path subject to dismantle from intermediate clamps of its fastening to the car bottom.
|
3. In most cases flexible hoses fasten to metal lines by means of collars of spring type. For отпускания a collar compress its flat-nose pliers and shift upwards on a hose. Deformed at отпускании the collar is not subject to a reuse and should be replaced. Track, that at connection the hose has been tense on a tube at least on 2.5 sm, in the correct image establish a fixing collar (address to an accompanying illustration). |
4. In some штуцерных knots sockets of fast joining are used, – for отпускания such socket it is necessary to compress its lock uvulas and to pull the connected lines every which way.
|
Needlessly do not remove the case of a socket with штуцерной a part of a metal tube as it leads to easing of keeping effort developed by it. |
5. Installation is made upside-down. On sockets of fast joining track for защелкиванием both lock uvulas in reception flutes. |
|
Repair
In case of damage of a metal or flexible fuel line it is necessary to replace the failed section only firm a corresponding standard size.
|
|