Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation



Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of position of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of a decorative lattice of a radiator
   Removal and installation of forward and back bumpers
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of external rear-view mirrors
   Removal, installation and adjustment of doors
   Removal and installation of forward wings
   Removal, installation and adjustment of a door of a back
   Removal and installation has flown down also a regulator стеклоподъемника back doors
   Removal and installation of door glasses
   Removal and installation of regulators стеклоподъемников
   Removal and installation of latches, замковых cylinders and door handles
   Removal and installation of a cover of the top hatch from a drive
   Removal and installation of a casing of a steering column
   Removal and installation of the central console
   Removal and installation finishing and main sections of the panel of devices
   Removal and installation of a lattice of an air inlet forward обтекателя
   Removal and installation of seats
   Removal and installation of an internal rear-view mirror
+ Onboard electric equipment


My new site https://www.psema4.com.



Removal, installation and adjustment of doors

Removal and installation

Forward door and its components


Car doors have considerable weight, therefore it will be reasonable to secure with the help of the assistant.


In order to avoid reception of cuts of hands about edges of technological windows in a doorframe work in gloves!


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped by a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

2. Remove the panel of an internal upholstery and film влагозащитный the screen (see Has undressed Removal and installation of panels of an internal upholstery of doors). At a corresponding complete set disunite contact sockets and liberate from intermediate clamps electroconducting of the actuation mechanisms located in a doorframe.

Preliminary it makes sense to mark disconnected wires.

3. Open a door against the stop and prop up its jack, or wooden blocks.

In order to avoid damage ЛКП lay between a head of a jack and edge of a door a rags layer.

4. Lead round loopy laths a marker, having marked their position on кузовном an element. Turn out fixing bolts (address to an illustration above) and by means of the assistant accurately remove door assemblage from the car. If the door is subject to replacement only, to remove loops from a rack does not follow.
5. Installation is made upside-down, track combination of the landing labels put in the course of dismantle. In case of need make adjustment.
6. Strongly tighten fixing bolts of loopy laths.

Adjustment

 PERFORMANCE ORDER

1. Adjustment of position of a door in an aperture plane is carried out by means of displacement of loops concerning a body. For this purpose it is necessary to weaken bolts of fastening of loops to a rack.
2. Adjustment of a ledge of a door from a body is carried out by means of displacement of a door concerning loops. For this purpose it is necessary to weaken bolts of fastening of a door to loops.
3. Serviceable operation запорного after door installation can achieve the mechanism by updating of position of the drummer of the lock in a vertical direction. For an estimation of size of displacement lead round a plate of the basis of the drummer a marker. Ослабьте fixture also make necessary adjustment, the latch should enter into gearing with the central part of the drummer. In summary adjust position of the drummer in the horizontal direction, the closed door should appear заподлицо with a surface of a rack/panel of a back wing and regularly thus be locked.