Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation



Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of position of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of a decorative lattice of a radiator
   Removal and installation of forward and back bumpers
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of external rear-view mirrors
   Removal, installation and adjustment of doors
   Removal and installation of forward wings
   Removal, installation and adjustment of a door of a back
   Removal and installation has flown down also a regulator стеклоподъемника back doors
   Removal and installation of door glasses
   Removal and installation of regulators стеклоподъемников
   Removal and installation of latches, замковых cylinders and door handles
   Removal and installation of a cover of the top hatch from a drive
   Removal and installation of a casing of a steering column
   Removal and installation of the central console
   Removal and installation finishing and main sections of the panel of devices
   Removal and installation of a lattice of an air inlet forward обтекателя
   Removal and installation of seats
   Removal and installation of an internal rear-view mirror
+ Onboard electric equipment





Removal and installation of a cover of the top hatch from a drive

At removal of internal overlays of an upholstery be reserved by various clip-on earrings – ри removal they often break.

Arrangement of elements of management of a cover of the top hatch


 PERFORMANCE ORDER

1. Remove following components:

  • Overlay of a threshold of a door of a back;
  • Back seat;
  • The left and right lateral upholstery;
  • Lateral overlay of a back seat;
  • Overlay of a threshold of a back door;
  • Forward bottom lateral overlay;
  • Facings of an aperture of a forward and back door;
  • The bottom overlay of the central rack;
  • Humeral clamp (anchor) of a seat belt of a forward seat;
  • The top facing of the central rack;
  • Seat belt regulator on height;
  • Both external clamps (anchor) of seat belts of a back seat;
  • Overlay of the third rack;
  • Overlay of a back rack;
  • The top handles;
  • Overlay of a forward rack and peaks with arms;
  • Internal rear-view mirror;
  • Forward and back lanterns of illumination of salon;
  • Facing of a doorway of a back;
  • Молдинг the top hatch;

2. Remove the management switch, having uncovered. Unfasten a cover from the case, turn away switch fastening. Separate a socket and remove the switch with an arm (address to an illustration above).
3. Remove clip-on earrings of fastening of the panel of a ceiling.
4. Dismantle the relay of management of a drive of a cover of the top hatch and disconnect from it a socket.
5. Turn away bolts of fastening of a drive with an arm. Remove a drive and separate a socket.
6. Remove hatch overlays. Having hooked from the inside, unhook clip-on earrings of overlays.
7. Remove hatch glass. Turn away a nut and remove washers. In total there should be six washers. Glass acts in film upwards.
8. Remove the drive tunnel.
9. Remove ветроотбойник.
10. Disconnect a drainage hose and remove the case of a cover of the hatch.
11. Adjust a trench of a drive of a cover of the hatch. A screw-driver shift draught forward or back for combination of two labels.
12. Adjust and establish drive knot as follows:

   a. Turn away the screw and uncover кулачковой plates;
   b. Turn away the big screw, remove washers;
   c. Turn a power shaft a screw-driver so that to combine dot labels on the case and a gear wheel;
   d. Establish a cover кулачковой plates, having fixed its screw;
   e. Establish knot of a drive and fix four bolts;
   f. Attach a socket.

13. Establish the relay of management of a drive together with an arm, attach a socket.
14. Establish the remained details in an order, the return to removal.