Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
- Transmissionnaja line
Specifications
Kardannye shaft and hinges - the general information
Condition check трансмиссионной lines
Removal and installation карданного a shaft
Replacement карданных hinges
Privodnye shaft/semiaxes, - the general information and condition check
Removal and installation of semiaxes, bearings and epiploons of the back bridge
Replacement of an epiploon of a leading gear wheel of differential
Removal and installation of assemblage of the back bridge
Removal and installation of power shafts
Replacement of protective covers and service of SHRUS
Removal and installation of assemblage of forward differential
Removal and installation of naves from a disconnected drive
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Replacement of protective covers and service of SHRUS
|
|
At revealing of defects of a protective cover the condition of a corresponding SHRUS should be carefully studied. Often on an exchange basis it is possible to get completely restored assemblages of power shafts that appreciably simplifies a situation and allows to reduce time expenses. Before to start dismantle of components, spend marketing, having found out the prices for necessary spare parts. Compare their expenses for acquisition of the restored assemblages. Remember that the external SHRUS is not subject to dismantling and varies in gathering with shaft.
|
Dismantling
Components of assemblage of a power shaft
|
|
1. Clamp a shaft in a vice with soft sponges. Check up the hinge on presence radial люфта, testifying to deterioration of internal components. Check up smoothness of a course of both hinges in all directions provided by their design. If the protective cover is damaged, disassemble the SHRUS, carefully wipe its components and estimate their condition.
2. By means of a small screw-driver unbend lock uvulas and remove bandage tapes of fastening of a protective cover.
3. Having hooked edge of a cover a screw-driver, remove it with шарнирной assemblages (the old and damaged covers can be cut simply off) (address to an illustration above). Remove the case of the hinge with триподной assemblages.
4. Mark position триподной assemblages on a shaft pin.
5. Remove a lock ring.
6. Having taken advantage brass выколоткой, bring down триподную assemblage from a shaft pin.
7. If yet did not cut off them, remove protective covers of both hinges. Wind equipped шлицами an internal pin of a shaft with a protective layer изоляционной tapes for protection of new covers against damage at their putting on on a shaft.
|
|
The external SHRUS is not subject to dismantling. |
|
|
Check
|
|
| Carefully wash out all components, including assemblage of an external SHRUS, in solvent, washout with all of them the rests of old greasing. Estimate a condition of working surfaces of bearings триподной assemblage and reciprocal surfaces in the case of the internal hinge. Directly to examine working surfaces of external and internal holders of the bearing of an external SHRUS it is not obviously possible, however indirectly it is possible to judge a condition on appearance of balls, turning the hinge, estimate a condition of all balls. If balls are not deformed and otherwise are not damaged, hence, also it is possible to consider holders being in good repair and the hinge is subject to the further use. In case of failure of components of an internal SHRUS шарнирная assemblage can be replaced. The external SHRUS varies in gathering with shaft. |
|
Assemblage
|
|
1. Put on a shaft protective covers of both SHRUS with bandage tapes of their fastening, trace plant on the regular place триподную assemblage, having fixed its lock ring. Fill greasing in bearings триподной assemblages and on a bottom of a cavity of the case of the hinge. Fill the end of a shaft with established триподной assemblage in the case of the hinge and fill in a cavity of the last the greasing rests.
2. Pull a cover on шарнирную assemblage, having tracked reliability of landing of its edges reception flutes. Adjust length of a shaft according to requirements of Specifications.
3. Having hooked external edge of the hinge, level pressure under it, then tighten fixing collars / bandage tapes.
4. Establish shaft assemblage on the car (see Has undressed Removal and installation of power shafts). |
|
|
|