Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation


Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
- Transmissionnaja line
   Specifications
   Kardannye shaft and hinges - the general information
   Condition check трансмиссионной lines
   Removal and installation карданного a shaft
   Replacement карданных hinges
   Privodnye shaft/semiaxes, - the general information and condition check
   Removal and installation of semiaxes, bearings and epiploons of the back bridge
   Replacement of an epiploon of a leading gear wheel of differential
   Removal and installation of assemblage of the back bridge
   Removal and installation of power shafts
   Replacement of protective covers and service of SHRUS
   Removal and installation of assemblage of forward differential
   Removal and installation of naves from a disconnected drive
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation карданного a shaft

 PERFORMANCE ORDER

Поддомкратьте the car also establish it on props. Translate a transmission in neutral position. A lay brake do not cock.

Back карданный a shaft

Removal

Assemblage back карданного a shaft is presented on an accompanying illustration.

Assemblage back карданного a shaft


 PERFORMANCE ORDER

1. Put adjusting labels on all flanges and шлицевые connections (address to an accompanying illustration) – in order to avoid balancing infringement at assemblage the shaft should be established strictly in the former position.
2. Turn out fastening bolts фланцевого a collar to back differential (address to an illustration above), for the purpose of providing of access to the next bolt turn a shaft / back wheels.
3. Lower the back end карданного a shaft, then release fixture соединительно a camshaft flange to a distributing box and liberate the forward end of a shaft from a box.

The description of procedures of replacement карданных hinges see in Section Replacement карданных hinges. Replacement of epiploons of differentials, is described in Section Replacement of an epiploon of a leading gear wheel of differential.

Installation

 PERFORMANCE ORDER

1. Carefully wipe a surface картера a distributing box round an entrance aperture карданного a shaft. Attentively check up an epiploon condition. Grease шлицевые connections and крестовины with multi-purpose greasing.
2. Приболтите хомутную hinge assemblage to a connecting flange, having tightened fixture while only by hand.
3. Lift the back end of a shaft in regular position, achieve combination of the landing labels put in the course of dismantle and fill in apertures fixing bolts.
4. Tighten nuts of fixing bolts with demanded effort. Clean props and lower the car on the earth.

Forward карданный a shaft

Removal

Assemblage forward карданного a shaft is presented on an accompanying illustration.

Assemblage back карданного a shaft


 PERFORMANCE ORDER

1a. Give fixture and remove the top dustproof cover of a shaft (address to an accompanying illustration).
1b. Cнимите the bottom dustproof cover of a shaft (address to an accompanying illustration).
2. Mark position карданного a shaft concerning connecting flanges of a distributing box and forward differential.
3. Give nuts of fixing bolts (do not forget about washers) and remove карданный a shaft.

The description of procedures of replacement карданных hinges is resulted in Section Replacement карданных hinges. Replacement of epiploons of differentials is described in Section Replacement of an epiploon of a leading gear wheel of differential.

Installation

 PERFORMANCE ORDER

1. Connect the forward end of a shaft to a connecting flange of differential. By hand tighten nuts of fixing bolts.
2. In appropriate way having modified length of a shaft, connect its back end to a flange of a distributing box. Tighten fixture with demanded effort.
3. Establish into place dustproof covers of a shaft.
4. Clean props and lower the car on the earth.