Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
- Transmissionnaja line
Specifications
Kardannye shaft and hinges - the general information
Condition check трансмиссионной lines
Removal and installation карданного a shaft
Replacement карданных hinges
Privodnye shaft/semiaxes, - the general information and condition check
Removal and installation of semiaxes, bearings and epiploons of the back bridge
Replacement of an epiploon of a leading gear wheel of differential
Removal and installation of assemblage of the back bridge
Removal and installation of power shafts
Replacement of protective covers and service of SHRUS
Removal and installation of assemblage of forward differential
Removal and installation of naves from a disconnected drive
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Replacement карданных hinges
|
|
For replacement performance карданных hinges the press or the big vice is required. |
|
|
1. Remove карданный a shaft (see Has undressed Removal and installation карданного a shaft).
2. Transfer карданный a shaft on the workbench equipped with a vice.
|
|
3a. Mark position of a collar concerning a shaft (address to an accompanying illustration). |
|
|
3b. Pатем remove lock rings (address to an accompanying illustration).
|
|
On models considered in the present Management bearings крестовин карданных hinges can be equipped by lock rings both external, and an internal design. External rings act in film by means of nippers, for extraction from the landing flutes of internal lock rings be required выколотка and a hammer. |
|
4. Press a piece of a pipe or a face head of the corresponding diameter to a cup of one of bearings (оправка should have internal diameter identical with a cup). Оправку slightly smaller diameter establish from the opposite end of a cup and, having clamped assemblage in a vice, squeeze out a cup outside (inside большей оправки) approximately on 25 mm.
|
|
Try not to supersede a cup completely from the landing nest in a collar cheek. |
5. Definitive extraction of a cup is made by means of nippers.
6. Operating in a similar manner, squeeze out a cup of the opposite bearing.
7. Take шарнирную assemblage from a collar and carefully it wipe. Make sure of absence задиров and scratches in landing nests in cheeks хомутной assemblages.
8. For deduction of rollers fill cups of the new bearing dense greasing.
|
|
The instruction on bearing greasing is usually put in packing of a standard repair set and should be observed strictly. |
9. Enclose шарнирную assemblage in a collar and partially fill in a landing nest a cup of one of bearings. If the hinge is equipped by the lubricant union, track, that it has appeared is developed in the same party, as the union of the hinge located from the opposite end of a shaft.
10. Enter a hinge body into a bearing cup, then partially fill a collar the second cup. Level the hinge between cups, then it is definitive запрессуйте the last in a collar, try not to damage пыльники.
11. Establish lock rings, in case of need sharply knock on a collar on purpose усадки rings in flutes. If the ring does not sit down even after обстукивания a collar, hence, there was a jamming of one of needle bearings крестовины, disassemble the hinge and repeat procedure.
|
|
12. Check up axial люфт in the hinge (address to an accompanying illustration) – if it more than 0.05 mm, pick up suitable lock rings. Rings are established by steams of an identical thickness on one axis that there were no vibrations. |
13. Establish карданный a shaft on the car (see Has undressed Removal and installation карданного a shaft).
14. If hinges are equipped by lubricant unions, fill their greasing (see the Head of Adjustment and car routine maintenance).
15. Clean props and lower the car on the earth. |
|
|
|