Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
- Brake system
Specifications
System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
Replacement brake колодок
Removal and installation of supports of disk brake mechanisms
Condition check, removal and installation of a brake disk
Removal and installation of the main brake cylinder (ГТЦ)
Check of a condition and replacement of brake lines and hoses
The valve sensitive to loading/perepusknoj (LSP and BP)
Adjustment of a lay brake
Replacement of cables of a drive of a lay brake
Check of serviceability of functioning / of tightness, removal and installation of the amplifier of brakes
Prorolling of brake system
Adjustment of a pedal of a foot brake
Check of serviceability of functioning and replacement of the gauge-switch of stoplights
Gauges and system ABS activator
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Adjustment of a pedal of a foot brake
Adjusting height of a pedal of a foot brake in the released condition
As height of position of a pedal of a foot brake is called the distance from the floor panel (the carpet covering does not act in film) to the central point of a surface of a rubber overlay колодки (address to an illustration above). If the result of measurement falls outside the limits an admissible range (Specifications see), it is necessary to make corresponding updating.
|
|
1. Disconnect electroconducting from the gauge-switch of stoplights (the Section Check of serviceability of functioning and replacement of the gauge-switch of stoplights see).
2. Give a counternut (the bottom nut) and remove the gauge-switch from the basic arm.
3. Ослабьте a counternut of a rod of a pusher of the vacuum amplifier of brakes.
4. Rotating a rod, make corresponding updating.
5. Strongly tighten a counternut.
6. Establish into place the gauge-switch of stoplights and make sure that it плунжер freely concerns a pedal emphasis. In case of need by means of adjusting a nut (the top nut) make corresponding updating.
7. Turn out the gauge-switch on one complete revolution.
|
|
8. Measure distance between the gauge-switch and a pedal emphasis (address to an accompanying illustration), size выступания плунжера), compare result of measurement to requirements |
Specifications. In case of need in appropriate way correct gauge-switch position on a basic arm.
9. Having finished adjustment, strongly tighten a counternut of the gauge-switch and connect to assemblage electroconducting.
10. Make sure of serviceability of operation of stoplights already at weak squeezing of a pedal of a foot brake. At отпускании pedals stoplights should die away.
11. Now it is necessary to measure size of a free wheeling of a pedal.
12. At the switched off engine some times squeeze out a pedal of a foot brake, having removed from assemblage of the vacuum amplifier residual depression.
|
|
13. A hand squeeze out a pedal to a point when there will be a sensation of resistance. Measure distance from колодки pedals to a floor and subtract result from height of adjusting position of the released pedal (address to an accompanying illustration). |
14. If the result of measurement falls outside the limits an admissible range (Specifications see), repeat adjustment of the gauge-switch of stoplights.
|
|
15. Check up size of a reserve course of a pedal: at the working engine (in the inlet pipeline depression should take place) squeeze out a pedal of a foot brake against the stop and make corresponding measurement (address to an accompanying illustration). |
16. Compare result of measurement to requirements of Specifications, in case of need make check of a condition of brake system.
17. Check up system on presence of signs of development of leaks. |
|
|
|