Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
- Brake system
Specifications
System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
Replacement brake колодок
Removal and installation of supports of disk brake mechanisms
Condition check, removal and installation of a brake disk
Removal and installation of the main brake cylinder (ГТЦ)
Check of a condition and replacement of brake lines and hoses
The valve sensitive to loading/perepusknoj (LSP and BP)
Adjustment of a lay brake
Replacement of cables of a drive of a lay brake
Check of serviceability of functioning / of tightness, removal and installation of the amplifier of brakes
Prorolling of brake system
Adjustment of a pedal of a foot brake
Check of serviceability of functioning and replacement of the gauge-switch of stoplights
Gauges and system ABS activator
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of supports of disk brake mechanisms
|
|
Remember that developed in the course of work of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system by gasoline or solvents on an oil basis, apply only firm cleaners or methyl spirit!
|
|
|
Supports of both brake mechanisms of one axis should vary simultaneously. Remember that on firm car repair shops Toyota always it is possible to order the restored assemblages of brake supports on an exchange basis.
|
Details of installation of brake supports are presented on illustrations of the Detail of installation of lobbies brake колодок and a support and the Detail of installation back brake колодок and a support.
|
|
1. Ослабьте nuts of fastening of forward wheels. Поддомкратьте redock of the car also establish it on props. Cock a lay brake/prop up противооткатными boots wheels standing on the earth. Remove wheels.
2. Pump out from tank GTTS approximately 2/3 brake liquids, at отжимании pistons level the liquid can start to be superseded from the tank. Get drain capacity under assemblage of the brake mechanism and process a surface of the last a special cleaner. Get drain capacity under assemblage of the corresponding brake mechanism and carefully wash out a surface of the last a special cleaner.
|
|
3. Give накидную штуцерную a nut and disconnect a brake line from a support (address to an accompanying illustration). |
|
|
4. Turn out bolts of fastening of a support (address to an accompanying illustration). If the support does not manage to be removed from a brake disk, hence, колодки cling for formed on border of deterioration of a disk a fillet, remove колодки (the Section Replacement brake колодок see). |
5. If the removed support is subject to the further use, carefully wash out it in a special cleaning liquid, at all do not use for washing of components of the brake mechanism kerosene and other mineral oil! Attentively check up a support condition, in case of need make its replacement.
6. Establish a support on the regular place and tighten with demanded effort fixing bolts.
7. Connect to a support a brake hose (do not forget to replace sealing washers). Strongly tighten накидную a nut штуцерного connections.
8. If disconnected a brake hose, pump over a corresponding brake contour (the Section Prorolling of brake system see).
9. Establish to the place of a wheel, lower the car on the earth and tighten wheel nuts with demanded effort (see the Head of Adjustment and car routine maintenance). Before to start vehicle operation make sure of serviceability of functioning of brake system. |
|
|
|