Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
- Brake system
Specifications
System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
Replacement brake колодок
Removal and installation of supports of disk brake mechanisms
Condition check, removal and installation of a brake disk
Removal and installation of the main brake cylinder (ГТЦ)
Check of a condition and replacement of brake lines and hoses
The valve sensitive to loading/perepusknoj (LSP and BP)
Adjustment of a lay brake
Replacement of cables of a drive of a lay brake
Check of serviceability of functioning / of tightness, removal and installation of the amplifier of brakes
Prorolling of brake system
Adjustment of a pedal of a foot brake
Check of serviceability of functioning and replacement of the gauge-switch of stoplights
Gauges and system ABS activator
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Replacement brake колодок
|
|
Replacement brake колодок should be made simultaneously on both forward/back brake mechanisms. Remember that developed in the course of work of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system gasoline or solvents on an oil basis, apply only firm cleaners or methyl spirit!
|
Details of installation of lobbies brake колодок and a support
Details of installation back brake колодок and a support
|
|
1. Details of installation brake колодок are presented on illustrations above. Ослабьте nuts of fastening of forward wheels. Поддомкратьте redock of the car also establish it on props. Cock a lay brake/prop up противооткатными boots wheels standing on the earth. Remove wheels.
2. Remove the spring clamp, directing pins, антивизговую a spring, колодки and антивизговые overlays.
3. After extraction колодки attentively examine internal surfaces of a support on presence of signs of development of leaks of a brake liquid, check up a condition пыльника the piston. Defective components are subject to replacement (see Has undressed Removal and installation of supports of disk brake mechanisms). Do not forget to study attentively also a condition of a brake disk (the Section condition Check, removal and installation of a brake disk see), in case of need give it in проточку.
|
|
4. Pump out a little a brake liquid from tank GTTS and wring out pistons in cylinders by means of a hammer or mount (address to an accompanying illustration). |
|
|
It is necessary to wind mount with an insulating tape. Make replacement by each support serially. For simplification of moving of the piston ослабьте the union of prorolling also move pistons at small leak of a brake liquid.
|
5. Establish new антивизговые overlays on new колодки and establish two колодки.
|
|
Put greasing for disk brakes on both parties internal антивизговых overlays. Greasing should not get on a working surface колодок or a disk. |
6. Establish антивизговую a spring, directing pins and a spring clamp.
7. Having finished service of both brake mechanisms, establish to the place of a wheel, lower the car on the earth and tighten wheel nuts with demanded effort (see the Head of Adjustment and car routine maintenance).
8. Check up level of a brake liquid in tank GTTS, in case of need make corresponding updating (see the Head of Adjustment and car routine maintenance). Some times rock a pedal of a foot brake for усадки колодок on disks, then repeat check of level of a liquid.
9. Before to start car operation make sure of serviceability of functioning of brake system. |
|
|
|