Toyota Land Cruiser 100 / Amazon, Lexus LX 470

Since 1997 of release

Repair and car operation



Tojota Lend Kruzer, Amazon, Leksus LX470
+ Identification numbers of the car
+ Controls and receptions of safe operation of the car
+ Options and car routine maintenance
+ The engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear change box
+ Transmissionnaja line
- Brake system
   Specifications
   System of antiblocking of brakes (ABS) - the general information and codes of malfunctions
   Replacement brake колодок
   Removal and installation of supports of disk brake mechanisms
   Condition check, removal and installation of a brake disk
   Removal and installation of the main brake cylinder (ГТЦ)
   Check of a condition and replacement of brake lines and hoses
   The valve sensitive to loading/perepusknoj (LSP and BP)
   Adjustment of a lay brake
   Replacement of cables of a drive of a lay brake
   Check of serviceability of functioning / of tightness, removal and installation of the amplifier of brakes
   Prorolling of brake system
   Adjustment of a pedal of a foot brake
   Check of serviceability of functioning and replacement of the gauge-switch of stoplights
   Gauges and system ABS activator
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation of the main brake cylinder (ГТЦ)

Failed ГТЦ is subject to replacement. It is not recommended to undertake attempt of carrying out of regenerative repair of the main brake cylinder.

Installation and assemblage ГТЦ components


 PERFORMANCE ORDER

1. Enclose rags under штуцерные connections and prepare caps or polyethylene packages for закупоривания the open ends of brake lines for the purpose of hit prevention in brake system of a dirt.

The brake liquid is among aggressive chemical compounds and at contact with кузовными panels destroys a paint and varnish covering. Before to start procedure performance cover wings and the panel передка the car with special covers, or simply old blankets.

2. Disconnect electroconducting of the gauge-switch of level of a brake liquid from tank GTTS (address to an illustration above).
3. By means of special накидного a key with a cutting head ослабьте nuts штуцерных connection knots to ГТЦ brake lines. Slightly having delayed outside, separate brake lines from unions of the main cylinder. At once закупорьте the open ends of tubes.
4. Give nuts of fastening ГТЦ. Watching that there was no twisting of hydraulic hoses, remove assemblage of the cylinder from the vacuum amplifier of brakes and take it from an impellent compartment.
5. Uncover tank GTTS and merge a brake liquid remaining inside in the prepared capacity.
6. After replacement ГТЦ all hydraulic path is subject to prorolling, thus затрачивание time can be reduced to prorolling at the expense of preliminary filling of the main cylinder and its prorolling on a workbench before installation (see more low)
7. For convenience clamp a landing flange of the cylinder in a vice with soft sponges and fill in in assemblage a fresh brake liquid.
8. Densely having pressed fingers to apertures under fastening of brake lines (фиттингам) in avoidance подсасывания in air cylinder, slowly push pistons in the cylinder (it will be most convenient to take advantage of the big screw-driver with a crosswise sting), air should start to leave delivery chambers in the tank. It is thus important, that the ends of both tubes have been completely shipped in a brake liquid being in the tank to exclude probability подсасывания air back in the cylinder at отпускании pistons.
9. Continue prorolling until the liquid pushed out through tubes completely will not be released from air bubbles.
10. Installation is made upside-down.
11. Having finished, pump over a hydraulic path. Before to start car operation, make sure of serviceability of functioning of brakes.